Kenmore Appliance
Repair

Kenmore does not manufacture appliances. Each Kenmore model is built by another company, so the first step on every call is the three-digit prefix before the dot in the model number. A 106 or 110 prefix means Whirlpool built it, 665 is a Whirlpool dishwasher, 253, 417, 587 and 790 point to Electrolux, and 795, 796 and 721 point to LG. Other models come from GE and smaller makers.

Once the builder is known, the Kenmore is diagnosed as that platform: same parts, same failure patterns, same tests. Whirlpool-built Kenmore top loaders and dryers are mechanically simple, while LG-built Kenmore Elite models bring inverter motors and linear compressors.

What breaks in Kenmore refrigerators

• Whirlpool-built (106). Defrost heater or thermostat failures that leave the fresh food side warm, evaporator fan noise and ice maker fill problems.
• LG-built (795). Ice buildup in the door ice compartment, freezer fan faults shown as Er FF, and linear compressor complaints that need sealed-system diagnosis.
• Electrolux-built (253). Air damper and fan faults that cause uneven temperatures, and ice maker issues.

When a compressor or refrigerant leak is the cause, we do the sealed-system repair in your kitchen.

How a refrigerator repair visit goes

What breaks in Kenmore washers

• Whirlpool-built top loaders (110). A failed shifter actuator or lid lock on newer models; worn motor couplings and agitator dogs on older direct-drive machines.
• Whirlpool-built front loaders. Drain pump clogs, torn door boots and tub bearings that roar in spin.
• LG-built (796). OE drain faults from a clogged pump filter, door lock faults, and rotor position sensor problems on the direct-drive motor.
• Electrolux-built (417). Door lock failures and drain pump faults on front loaders.

How a washer repair visit goes

What breaks in Kenmore dryers

• Whirlpool-built (110). The Kenmore dryer we see most: broken belts, worn drum rollers and idler pulleys, thermal fuses blown by restricted exhaust, and burned heating elements.
• LG-built (796). Worn drum glides and front felt seal that squeak, plus thermistor and heater faults.
• Electrolux-built (417). A worn rear drum bearing and glides, and igniter or valve coil failures on gas models.

On any gas Kenmore, an igniter that glows but never lights the burner usually points to weak valve coils.

How a dryer repair visit goes

What breaks in Kenmore dishwashers

• Whirlpool-built (665). Drain pump and chopper clogs, failed diverter motors that leave one rack dirty, door latch switches and heating elements.
• Electrolux-built (587). Wash motor failures, drain pumps, control boards and door latch problems, plus leaks at the door gasket or sump.

On both, the first check is the filter and drain path, because a restriction shows up as poor cleaning, standing water or a fault display. We confirm the root cause before ordering a pump or board.

How a dishwasher repair visit goes

What breaks in Kenmore ranges and ovens

Many Kenmore ranges carry the 790 prefix, meaning Electrolux built them on the same platform as Frigidaire ranges.

• Oven not heating. A burned bake element on electric models, a weak glow-bar igniter on gas models.
• F10 or F30 on the display. The oven sensor or its connection, sometimes the control board.
• F11 or dead keys. A shorted or worn touch panel.
• Door stuck after self-clean. The door lock motor or its switch.

How an oven or range repair visit goes

What breaks in Kenmore cooktops

• Radiant element dead or stuck on high. A burned element or failed infinite switch, both common on Electrolux-built smooth tops.
• Hot surface light stays on. A failed limiter or switch.
• Gas burners clicking or slow to light. A wet ignition switch, a cracked igniter or a failing spark module, or burner ports clogged by spills.
• Induction zone off or showing a fault. Kenmore induction tops with a 790 prefix are Electrolux-built; power board and cooling fan faults are typical there.

How a cooktop repair visit goes

What breaks in Kenmore microwaves

• LG-built (721) over-the-range units. No heat from a failed magnetron, high-voltage diode or capacitor; dead units from a door switch failure that blew the main fuse; touch panels that stop responding.
• Turntable not turning. The motor or coupler.
• Vent fan or light out. The hood section of an over-the-range Kenmore has its own motor and switches.

We discharge the high-voltage capacitor before any test, since it holds a dangerous charge.

How a microwave repair visit goes

What breaks in Kenmore range hoods

Kenmore hoods are mostly under-cabinet and wall chimney units from various suppliers, so we match parts by the full model number.

• Fan noisy or slow. A grease-caked blower wheel or tired motor bearings.
• Fan or light switch dead. Rocker or slide switches wear out; newer units use a touch control board.
• Lights out. A bulb socket damaged by heat or a failed LED driver.
• Poor draw. Clogged grease filters or a stuck damper.

How a range hood repair visit goes

Parts and warranty on Kenmore repairs

We install OEM parts only, and on a Kenmore that means the builder's parts: Whirlpool parts for a 106 or 110 model, LG parts for 795 or 796, Electrolux parts for 790 or 417. Kenmore part numbers usually cross-reference to the builder's own, so most functional parts remain available even on older models, while Kenmore-only knobs and panels are harder to find. If your Kenmore is still under its manufacturer warranty, use that first. Our repairs carry a 90-day labor warranty.

Kenmore codes we see most often

These are the display codes that bring us the most Kenmore calls. The wording is ours, and the meaning can shift between model years, so treat the table as a starting point: a technician confirms the cause with tests before any part is replaced.